News

27th July 2022

K-Face – Mould Temperature Alarm Interface For Operators

What is K-Face? K-Face Basic is an LCD screen Temperature Alarm Interface that displays the temperature on one channel to the machine operator. This alerts the operator as to when the mould is ready to be removed from the oven (or, in the case of an open-flame machine, when to turn off the gas) and […]

Read More

21st July 2022

Busy day yesterday here at 493K making up some samples using the RotoRocket! 🚀 #rotomolding #rotomoulding #493kltd https://t.co/weTfiQs8cv

Busy day yesterday here at 493K making up some samples using the RotoRocket! 🚀 #rotomolding #rotomoulding #493kltd https://t.co/weTfiQs8cv

Read More

14th July 2022

K-Label

Vent Mounted, peak air temperature recorded. Certified and filed… job done. Numerous studies have demonstrated that the peak internal mould air temperature gives a good indication of the state of the rotomoulded part. K-Label provides a simple quality control method to check that the moulding has obtained correct cure and avoided under or over curing. […]

Read More

7th July 2022

RotoRocket – Now Available With Optional Hexagonal Mould!

A uni-axial benchtop rotational moulding machine, complete with glass mould and an optional hexagonal mould! demonstrate – educate – experiment Experience the rotomoulding process, as rarely seen before, through the RotoRocket’s unique glass mould. The RotoRocket comes complete with integrated heaters and temperature monitoring.  This means that a full rotomoulding part can be made and observed not […]

Read More

1st July 2022

K-Paq: Portable temperature & pressure measurement for rotomoulding…

Reduce cycle times, optimise processing, know what’s going on inside your mould… K-Paq is a 4 channel portable device that conveniently attaches to a rotational mould, measuring mould pressure via the vent pipe and mould temperature via type K thermocouples. This is done in real time, allowing the moulder to identify faults immediately and observe the response […]

Read More

24th June 2022

Dr. Gareth calibrating K-Metron, a part wall thickness meter, to take along to the BPF’s Rotational Moulding seminar…

Dr. Gareth calibrating K-Metron, a part wall thickness meter, to take along to the BPF’s Rotational Moulding seminar… https://t.co/97zeDEXgYE

Read More

21st June 2022

K-Metron thickness measurement of rotomoulded, composites or any non-ferrous part walls now up to 30mm!…

K-Metron thickness measurement of rotomoulded, composites or any non-ferrous part walls now up to 30mm!… https://t.co/yLfWUi08K9

Read More

19th January 2021

Are you a Rotomoulder with a penchant for the Panda life?

Beologic can even add Bamboo to your Rotograde PE material and still let you rotomould it… so maybe it’s time to break out your inner Panda and give them a call. A brief review by Dr. Gareth on Beologic’s bio-based rotomoulding composite: Bamboo & PE! What could you rotomould with this? For more info drop […]

Read More

30th September 2020

Are you a stone cold rotomoulder?

A brief review by Dr. Gareth on Beologic’s bio-based rotomoulding composite: Basalt & PE! What could you rotomould with this? For more info drop us a line: sales@493k.com

Read More

21st January 2017

Preparing for the Indian Star rotomoulding conference. https://t.co/p7NFGBzvvM https://t.co/QaGqDi4wtJ

Preparing for the Indian Star rotomoulding conference. https://t.co/p7NFGBzvvM https://t.co/QaGqDi4wtJ

Read More